Dell Edge Gateway 3002

The Edge Gateway 3002 is one of a series of “IoT edge devices” that Dell introduced around 2019. There are three models in the 3000 series: the 3001, intended for general purpose “IoT stuff” with lots of GPIO, the 3002, which includes GPS, Zigbee, and CAN bus, and the 3003, which has displayport and is intended for digital signage applications. The 3001 and 3002 have no video output whatsoever.

General Notes

Specs

  • Intel Atom E3805 2x 1.33GHz
  • 2GB RAM (DDR3L @ 1600MHz)
  • 8GB eMMC (Kingston W32508)
  • 2x Realtek RTL8101 at 10/100. Port 1 (eth0) supports PoE power input!
  • SiLabs RS9113 WiFi+Bluetooth over SDIO
  • Ublox UBX-M8030 GNSS - connected at /dev/ttyHS1
  • ZigBee 2.4GHz - Attached at /dev/ttyHS0 (SiLabs ETRX3587HR)
  • CAN bus on /dev/ttyACM0 - Atmel ATSAME70N19A-CNT. Exposed on 3pin Phoenix header on the side.
  • Environmental Sensors
    • ST Micro HTS221 - Temperature
    • ST Micro LNG2DMTR - Accelerometer
    • ST Micro LPS22HB - Barometric Pressure

Available External Interfaces

  • 2x RJ-45 Ethernet
  • 1x USB 3.0 (600mA)
  • 1x USB 2.0 (400mA)
  • SMA-F for GNSS/WiFi+BT
  • SMA-F for Zigbee
  • (2x additional openings for SMA available)
  • 3 pin phoenix connector for CAN bus
  • 3 pin phoenix connector for power 12-57v DC (plus ignition detection)
  • 3.5mm jack for external intrusion detection
  • uSD slot behind screwed down door
  • 3x LEDs
    • Power LED (orange/green, shows generic status info)
    • “Antenna” LED (green, not sure how it's controlled)
    • “Cloud” LED (green, controlled by end user though GPIO sysfs)

Available Internal Interfaces

  • 4 pin JST micro connector for ttyS0 (115200,8n1 for boot console)
  • MiniPCIe connector (not soldered, likely needs additional hardware)
  • Four switches exist inside the device (two 2 switch modules) but it is not yet clear exactly what they do.

No user upgradable RAM/storage.

Local Console Access

The 3002 was designed to be accessed entirely over a network, and has no end user ways to accessing a local console. Under the lid there is a four pin JST micro connector (same physical connector as Qwiic) that can be used to access ttyS0, which has console output on boot. This is a 1v8 UART running at 115200,8n1.

UEFI Access

The 3002 has no video output, and was designed to have the BIOS be accessed via a tool called Dell Command Configure Version. This can be installed via debs available here:

command-configure_4.2.0-553.ubuntu16_amd64.tar.gz

This works in Ubuntu 18.04. Have not yet tested it in other distros.

Environmental Sensors

GNSS

The UBX-M8030 can be accessed via /dev/ttyHS1 running at 9600,8n1 by default. It supports three concurrent SVs (GPS, GLONASS, and BeiDou) and is very sensitive. The GNSS module and WiFi+BT module share an RF connection for some reason, and as such the GNSS does not provide any power for an active antenna.

We are currently researching how to add power to this connection to support an active antenna, which greatly improves the performance of most GNSS antennas which have built in low noise amplifiers (LNAs).

Temp/Humidity/Pressure/Accelerometer

The 3002 has three ST Micros environmental sensors that can be accessed through i2c sysfs. More info here.

Update Firmware

This may need to be done on one of the original dell-provided images. I'd recommend upgrading firmware before installing another OS.

Online
fwupdmgr get-devices
fwupdmgr refresh
fwupdmgr get-updates
fwupdmgr update -v
Offline

3000 Series v1.11.0 (from here)

fwupdmgr get-devices
fwupdmgr get-details /path/to/*-firmware.cab
fwupdmgr install /path/to/*-firmware.cab -v
sudo reboot

Flash Recovery Image

More testing needed. Watch this space!

Hardware Details

lshw

4f4hp42
    description: Computer
    product: Edge Gateway 3002 (07B9)
    vendor: Dell Inc.
    serial: 4F4HP42
    width: 64 bits
    capabilities: smbios-3.0 dmi-3.0 smp vsyscall32
    configuration: boot=normal family=Edge Gateway sku=07B9 uuid=44454C4C-4600-1034-8048-B4C04F503432
  *-core
       description: Motherboard
       product: 03MDH6
       vendor: Dell Inc.
       physical id: 0
       version: A01
       serial: /4F4HP42/CNPE1009AE008N/
     *-firmware
          description: BIOS
          vendor: Dell Inc.
          physical id: 0
          version: 1.11.00
          date: 11/11/2022
          size: 64KiB
          capacity: 15MiB
          capabilities: pci pnp upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb biosbootspecification netboot uefi
     *-memory
          description: System Memory
          physical id: 26
          slot: System board or motherboard
          size: 2GiB
          capabilities: ecc
          configuration: errordetection=multi-bit-ecc
        *-bank:0
             description: DIMM DDR3 1600 MHz (0.6 ns)
             product: Array1_PartNumber0
             vendor: A1_Manufacturer0
             physical id: 0
             serial: A1_SerNum0
             slot: A1_DIMM0
             size: 2GiB
             width: 64 bits
             clock: 1600MHz (0.6ns)
        *-bank:1
             description: DIMM [empty]
             product: Array1_PartNumber1
             vendor: A1_Manufacturer1
             physical id: 1
             serial: A1_SerNum1
             slot: A1_DIMM1
     *-cache:0
          description: L1 cache
          physical id: 32
          slot: CPU Internal L1
          size: 112KiB
          capacity: 112KiB
          capabilities: internal write-back
          configuration: level=1
     *-cache:1
          description: L2 cache
          physical id: 33
          slot: CPU Internal L2
          size: 1MiB
          capacity: 1MiB
          capabilities: internal write-back unified
          configuration: level=2
     *-cpu
          description: CPU
          product: Intel(R) Atom(TM) CPU  E3805  @ 1.33GHz
          vendor: Intel Corp.
          physical id: 34
          bus info: cpu@0
          version: Intel(R) Atom(TM) CPU E3805 @ 1.33GHz
          slot: SOCKET 0
          size: 533MHz
          capacity: 2400MHz
          width: 64 bits
          clock: 133MHz
          capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb pti ibrs ibpb stibp tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm arat cpufreq
          configuration: cores=2 enabledcores=2 threads=2
     *-pci
          description: Host bridge
          product: Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register
          vendor: Intel Corporation
          physical id: 100
          bus info: pci@0000:00:00.0
          version: 11
          width: 32 bits
          clock: 33MHz
          configuration: driver=iosf_mbi_pci
          resources: irq:0
        *-usb
             description: USB controller
             product: Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI
             vendor: Intel Corporation
             physical id: 14
             bus info: pci@0000:00:14.0
             version: 11
             width: 64 bits
             clock: 33MHz
             capabilities: pm msi xhci bus_master cap_list
             configuration: driver=xhci_hcd latency=0
             resources: irq:87 memory:80400000-8040ffff
           *-usbhost:0
                product: xHCI Host Controller
                vendor: Linux 4.15.0-1031-oem xhci-hcd
                physical id: 0
                bus info: usb@1
                logical name: usb1
                version: 4.15
                capabilities: usb-2.00
                configuration: driver=hub slots=6 speed=480Mbit/s
              *-usb
                   description: Communication device
                   vendor: Atmel Corp.
                   physical id: 4
                   bus info: usb@1:4
                   version: 1.00
                   serial: USB CAN FD Application v.B
                   capabilities: usb-2.00
                   configuration: driver=cdc_acm maxpower=100mA speed=480Mbit/s
           *-usbhost:1
                product: xHCI Host Controller
                vendor: Linux 4.15.0-1031-oem xhci-hcd
                physical id: 1
                bus info: usb@2
                logical name: usb2
                version: 4.15
                capabilities: usb-3.00
                configuration: driver=hub slots=1 speed=5000Mbit/s
        *-generic
             description: Encryption controller
             product: Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine
             vendor: Intel Corporation
             physical id: 1a
             bus info: pci@0000:00:1a.0
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pm msi bus_master cap_list
             configuration: driver=mei_txe latency=0
             resources: irq:91 memory:80100000-801fffff memory:80000000-800fffff
        *-pci:0
             description: PCI bridge
             product: Atom Processor E3800 Series PCI Express Root Port 1
             vendor: Intel Corporation
             physical id: 1c
             bus info: pci@0000:00:1c.0
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:16 ioport:1000(size=4096)
        *-pci:1
             description: PCI bridge
             product: Atom Processor E3800 Series PCI Express Root Port 2
             vendor: Intel Corporation
             physical id: 1c.1
             bus info: pci@0000:00:1c.1
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:17 ioport:d000(size=4096) memory:80300000-803fffff
           *-network
                description: Ethernet interface
                product: RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller
                vendor: Realtek Semiconductor Co., Ltd.
                physical id: 0
                bus info: pci@0000:02:00.0
                logical name: eth0
                version: 07
                serial: 00:4e:01:b9:aa:25
                size: 100Mbit/s
                capacity: 100Mbit/s
                width: 64 bits
                clock: 33MHz
                capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
                configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8106e-1_0.0.1 06/29/12 ip=172.16.0.110 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s
                resources: irq:89 ioport:d000(size=256) memory:80304000-80304fff memory:80300000-80303fff
        *-pci:2
             description: PCI bridge
             product: Atom Processor E3800 Series PCI Express Root Port 3
             vendor: Intel Corporation
             physical id: 1c.2
             bus info: pci@0000:00:1c.2
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:18 ioport:2000(size=4096)
        *-pci:3
             description: PCI bridge
             product: Atom Processor E3800 Series PCI Express Root Port 4
             vendor: Intel Corporation
             physical id: 1c.3
             bus info: pci@0000:00:1c.3
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:19 ioport:c000(size=4096) memory:80200000-802fffff
           *-network
                description: Ethernet interface
                product: RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller
                vendor: Realtek Semiconductor Co., Ltd.
                physical id: 0
                bus info: pci@0000:04:00.0
                logical name: eth1
                version: 07
                serial: 00:4e:01:b9:aa:26
                size: 10Mbit/s
                capacity: 100Mbit/s
                width: 64 bits
                clock: 33MHz
                capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
                configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8106e-1_0.0.1 06/29/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s
                resources: irq:90 ioport:c000(size=256) memory:80204000-80204fff memory:80200000-80203fff
        *-isa
             description: ISA bridge
             product: Atom Processor Z36xxx/Z37xxx Series Power Control Unit
             vendor: Intel Corporation
             physical id: 1f
             bus info: pci@0000:00:1f.0
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: isa bus_master cap_list
             configuration: driver=lpc_ich latency=0
             resources: irq:0
        *-serial
             description: SMBus
             product: Atom Processor E3800 Series SMBus Controller
             vendor: Intel Corporation
             physical id: 1f.3
             bus info: pci@0000:00:1f.3
             version: 11
             width: 32 bits
             clock: 33MHz
             capabilities: pm cap_list
             configuration: driver=i801_smbus latency=0
             resources: irq:18 memory:80418000-8041801f ioport:e000(size=32)
  *-network
       description: Wireless interface
       physical id: 1
       logical name: wlan0
       serial: 88:da:1a:67:17:38
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=RSI-SDIO WLAN driverversion=4.15.0-1031-oem firmware=N/A link=no multicast=yes wireless=IEEE 802.11
       

lscpu

Architecture:        x86_64
CPU op-mode(s):      32-bit, 64-bit
Byte Order:          Little Endian
CPU(s):              2
On-line CPU(s) list: 0,1
Thread(s) per core:  1
Core(s) per socket:  2
Socket(s):           1
NUMA node(s):        1
Vendor ID:           GenuineIntel
CPU family:          6
Model:               55
Model name:          Intel(R) Atom(TM) CPU  E3805  @ 1.33GHz
Stepping:            9
CPU MHz:             850.726
CPU max MHz:         1333.0000
CPU min MHz:         533.2000
BogoMIPS:            2666.00
Virtualization:      VT-x
L1d cache:           24K
L1i cache:           32K
L2 cache:            512K
NUMA node0 CPU(s):   0,1
Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb pti ibrs ibpb stibp tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm arat

lspci

00:00.0 Host bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register (rev 11)
00:14.0 USB controller: Intel Corporation Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI (rev 11)
00:1a.0 Encryption controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine (rev 11)
00:1c.0 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 1 (rev 11)
00:1c.1 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 2 (rev 11)
00:1c.2 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 3 (rev 11)
00:1c.3 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 4 (rev 11)
00:1f.0 ISA bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit (rev 11)
00:1f.3 SMBus: Intel Corporation Atom Processor E3800 Series SMBus Controller (rev 11)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 07)
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 07)

lsusb

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 03eb:2404 Atmel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

dmesg

[    0.000000] Linux version 4.15.0-1031-oem (buildd@lcy01-amd64-006) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #36-Ubuntu SMP Mon Jan 7 09:40:58 UTC 2019 (Ubuntu 4.15.0-1031.36-oem 4.15.18)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-1031-oem root=UUID=b8099873-ca89-4a7d-8654-118a06b57184 ro quiet splash resume=UUID=b8099873-ca89-4a7d-8654-118a06b57184 console=ttyS0,115200n8 net.ifnames=0 fixrtc sdhci.debug_quiks2=0x80 resume=UUID=7c49b0dd-1fa1-41ce-acab-25b5cb5177cb
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000003efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000003f000-0x000000000003ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000000040000-0x000000000009cfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000200fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020100000-0x0000000076be0fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000076be1000-0x0000000076c58fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000076c59000-0x0000000076c69fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x0000000076c6a000-0x00000000771f3fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000771f4000-0x0000000077528fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000077529000-0x0000000077529fff] usable
[    0.000000] BIOS-e820: [mem 0x000000007752a000-0x000000007756bfff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007756c000-0x00000000789e4fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000789e5000-0x0000000078ff9fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000078ffa000-0x0000000078ffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed0c000-0x00000000fed0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fef00000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff900000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.40 by American Megatrends
[    0.000000] efi:  ACPI=0x76c5c000  ACPI 2.0=0x76c5c000  SMBIOS=0xf0000  ESRT=0x773a6598
[    0.000000] secureboot: Secure boot disabled
[    0.000000] SMBIOS 3.0 present.
[    0.000000] DMI: Dell Inc. Edge Gateway 3002/03MDH6, BIOS 1.11.00 11/11/2022
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x79000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 079000000 mask FFF000000 uncachable
[    0.000000]   2 base 07A000000 mask FFE000000 uncachable
[    0.000000]   3 base 07C000000 mask FFC000000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT
[    0.000000] total RAM covered: 1936M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K 	chunk_size: 128M 	num_reg: 4  	lose cover RAM: 0G
[    0.000000] esrt: Reserving ESRT space from 0x00000000773a6598 to 0x00000000773a65d0.
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [        (ptrval)] 97000 size 24576
[    0.000000] BRK [0x0c342000, 0x0c342fff] PGTABLE
[    0.000000] BRK [0x0c343000, 0x0c343fff] PGTABLE
[    0.000000] BRK [0x0c344000, 0x0c344fff] PGTABLE
[    0.000000] BRK [0x0c345000, 0x0c345fff] PGTABLE
[    0.000000] BRK [0x0c346000, 0x0c346fff] PGTABLE
[    0.000000] BRK [0x0c347000, 0x0c347fff] PGTABLE
[    0.000000] BRK [0x0c348000, 0x0c348fff] PGTABLE
[    0.000000] BRK [0x0c349000, 0x0c349fff] PGTABLE
[    0.000000] BRK [0x0c34a000, 0x0c34afff] PGTABLE
[    0.000000] BRK [0x0c34b000, 0x0c34bfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x396f3000-0x3cc05fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x0000000076C5C000 000024 (v02 DELL  )
[    0.000000] ACPI: XSDT 0x0000000076C5C088 00008C (v01 DELL   AS09     01072009 AMI  00010013)
[    0.000000] ACPI: FACP 0x0000000076C68550 00010C (v05 DELL   AS09     01072009 AMI  00010013)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20170831/tbfadt-603)
[    0.000000] ACPI: DSDT 0x0000000076C5C1A0 00C3AF (v02 DELL   AS09     01072009 INTL 20120913)
[    0.000000] ACPI: FACS 0x00000000771F3E80 000040
[    0.000000] ACPI: APIC 0x0000000076C68660 000068 (v03 DELL   AS09     01072009 AMI  00010013)
[    0.000000] ACPI: FPDT 0x0000000076C686C8 000044 (v01 DELL   AS09     01072009 AMI  00010013)
[    0.000000] ACPI: FIDT 0x0000000076C68710 00009C (v01 DELL   AS09     01072009 AMI  00010013)
[    0.000000] ACPI: MCFG 0x0000000076C687B0 00003C (v01 DELL   AS09     01072009 MSFT 00000097)
[    0.000000] ACPI: LPIT 0x0000000076C687F0 000104 (v01 DELL   AS09     00000003 VLV2 0100000D)
[    0.000000] ACPI: HPET 0x0000000076C688F8 000038 (v01 DELL   AS09     01072009 AMI. 00000005)
[    0.000000] ACPI: SSDT 0x0000000076C68930 000763 (v01 DELL   AS09     00003000 INTL 20061109)
[    0.000000] ACPI: SSDT 0x0000000076C69098 000290 (v01 DELL   AS09     00003000 INTL 20061109)
[    0.000000] ACPI: SSDT 0x0000000076C69328 00017A (v01 DELL   AS09     00003000 INTL 20061109)
[    0.000000] ACPI: UEFI 0x0000000076C694A8 000042 (v01 DELL   AS09     00000000      00000000)
[    0.000000] ACPI: CSRT 0x0000000076C694F0 00014C (v00 DELL   AS09     00000005 INTL 20120624)
[    0.000000] ACPI: TPM2 0x0000000076C69640 000034 (v03        Tpm2Tabl 00000001 AMI  00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x0000000078ffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x765bc000-0x765e6fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x0000000078ffffff]
[    0.000000]   Normal   empty
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000003efff]
[    0.000000]   node   0: [mem 0x0000000000040000-0x000000000009cfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.000000]   node   0: [mem 0x0000000020100000-0x0000000076be0fff]
[    0.000000]   node   0: [mem 0x0000000077529000-0x0000000077529fff]
[    0.000000]   node   0: [mem 0x000000007756c000-0x00000000789e4fff]
[    0.000000]   node   0: [mem 0x0000000078ffa000-0x0000000078ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000078ffffff]
[    0.000000] On node 0 totalpages: 491260
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3995 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7680 pages used for memmap
[    0.000000]   DMA32 zone: 487265 pages, LIFO batch:31
[    0.000000] Reserved but unavailable: 99 pages
[    0.000000] x86/hpet: Will disable the HPET for this platform because it's not reliable
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-86
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0003f000-0x0003ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x20000000-0x200fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x76be1000-0x76c58fff]
[    0.000000] PM: Registered nosave memory: [mem 0x76c59000-0x76c69fff]
[    0.000000] PM: Registered nosave memory: [mem 0x76c6a000-0x771f3fff]
[    0.000000] PM: Registered nosave memory: [mem 0x771f4000-0x77528fff]
[    0.000000] PM: Registered nosave memory: [mem 0x7752a000-0x7756bfff]
[    0.000000] PM: Registered nosave memory: [mem 0x789e5000-0x78ff9fff]
[    0.000000] e820: [mem 0x79000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] random: get_random_bytes called from start_kernel+0x99/0x4fd with crng_init=0
[    0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] percpu: Embedded 46 pages/cpu @        (ptrval) s151552 r8192 d28672 u1048576
[    0.000000] pcpu-alloc: s151552 r8192 d28672 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 483495
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-1031-oem root=UUID=b8099873-ca89-4a7d-8654-118a06b57184 ro quiet splash resume=UUID=b8099873-ca89-4a7d-8654-118a06b57184 console=ttyS0,115200n8 net.ifnames=0 fixrtc sdhci.debug_quiks2=0x80 resume=UUID=7c49b0dd-1fa1-41ce-acab-25b5cb5177cb
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 1739516K/1965040K available (12300K kernel code, 2476K rwdata, 4284K rodata, 2416K init, 2416K bss, 225524K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] ftrace: allocating 39479 entries in 155 pages
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=2.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 524544, nr_irqs: 512, preallocated irqs: 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [ttyS0] enabled
[    0.000000] ACPI: Core revision 20170831
[    0.000000] ACPI: 4 ACPI AML tables successfully acquired and loaded
[    0.004000] APIC: Switch to symmetric I/O mode setup
[    0.004000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.024000] tsc: Detected 1333.000 MHz processor
[    0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 2666.00 BogoMIPS (lpj=5332000)
[    0.024000] pid_max: default: 32768 minimum: 301
[    0.024000] Security Framework initialized
[    0.024000] Yama: becoming mindful.
[    0.024000] AppArmor: AppArmor initialized
[    0.024000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.024000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.024000] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.024000] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.024000] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.024000] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.024000] mce: CPU supports 6 MCE banks
[    0.024000] process: using mwait in idle threads
[    0.024000] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    0.024000] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[    0.024000] Spectre V2 : Mitigation: Full generic retpoline
[    0.024000] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.024000] Spectre V2 : Spectre v2 mitigation: Enabling Indirect Branch Prediction Barrier
[    0.024000] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.028139] Freeing SMP alternatives memory: 36K
[    0.043375] TSC deadline timer enabled
[    0.043381] smpboot: CPU0: Intel(R) Atom(TM) CPU  E3805  @ 1.33GHz (family: 0x6, model: 0x37, stepping: 0x9)
[    0.043664] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[    0.043695] ... version:                3
[    0.043697] ... bit width:              40
[    0.043699] ... generic registers:      2
[    0.043701] ... value mask:             000000ffffffffff
[    0.043703] ... max period:             0000007fffffffff
[    0.043704] ... fixed-purpose events:   3
[    0.043706] ... event mask:             0000000700000003
[    0.043829] Hierarchical SRCU implementation.
[    0.044000] smp: Bringing up secondary CPUs ...
[    0.044000] x86: Booting SMP configuration:
[    0.044000] .... node  #0, CPUs:      #1
[    0.044186] smp: Brought up 1 node, 2 CPUs
[    0.044190] smpboot: Max logical packages: 1
[    0.044195] smpboot: Total of 2 processors activated (5332.00 BogoMIPS)
[    0.044483] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.045177] devtmpfs: initialized
[    0.045177] x86/mm: Memory block size: 128MB
[    0.045177] evm: security.selinux
[    0.045177] evm: security.SMACK64
[    0.045177] evm: security.SMACK64EXEC
[    0.045177] evm: security.SMACK64TRANSMUTE
[    0.045177] evm: security.SMACK64MMAP
[    0.045177] evm: security.apparmor
[    0.045177] evm: security.ima
[    0.045177] evm: security.capability
[    0.045473] PM: Registering ACPI NVS region [mem 0x0003f000-0x0003ffff] (4096 bytes)
[    0.045478] PM: Registering ACPI NVS region [mem 0x76c6a000-0x771f3fff] (5808128 bytes)
[    0.045954] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.045954] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.045954] pinctrl core: initialized pinctrl subsystem
[    0.045954] RTC time: 16:15:14, date: 01/01/12
[    0.048109] NET: Registered protocol family 16
[    0.048474] audit: initializing netlink subsys (disabled)
[    0.048591] audit: type=2000 audit(1325434514.048:1): state=initialized audit_enabled=0 res=1
[    0.049059] cpuidle: using governor ladder
[    0.049059] cpuidle: using governor menu
[    0.049059] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.049059] ACPI: bus type PCI registered
[    0.049059] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.049059] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.049059] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.049059] PCI: Using configuration type 1 for base access
[    0.054507] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.054507] ACPI: Added _OSI(Module Device)
[    0.054507] ACPI: Added _OSI(Processor Device)
[    0.054507] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.054507] ACPI: Added _OSI(Processor Aggregator Device)
[    0.054507] ACPI: Added _OSI(Linux-Dell-Video)
[    0.054507] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.084940] ACPI: Dynamic OEM Table Load:
[    0.084960] ACPI: SSDT 0xFFFF8BCBAE2AF000 0002B4 (v01 PmRef  Cpu0Ist  00003000 INTL 20061109)
[    0.086222] ACPI: Dynamic OEM Table Load:
[    0.086239] ACPI: SSDT 0xFFFF8BCBAE230800 000433 (v01 PmRef  Cpu0Cst  00003001 INTL 20061109)
[    0.088928] ACPI: Dynamic OEM Table Load:
[    0.088944] ACPI: SSDT 0xFFFF8BCBAE31E400 00015F (v01 PmRef  ApIst    00003000 INTL 20061109)
[    0.090048] ACPI: Dynamic OEM Table Load:
[    0.090064] ACPI: SSDT 0xFFFF8BCBAE2F0000 00008D (v01 PmRef  ApCst    00003000 INTL 20061109)
[    0.094178] ACPI: Interpreter enabled
[    0.094255] ACPI: (supports S0 S3 S4 S5)
[    0.094259] ACPI: Using IOAPIC for interrupt routing
[    0.094396] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.096211] ACPI: GPE 0x02 active on init
[    0.096252] ACPI: Enabled 6 GPEs in block 00 to 3F
[    0.121970] ACPI: Power Resource [USBC] (on)
[    0.128125] ACPI: Power Resource [PLPE] (on)
[    0.129699] ACPI: Power Resource [PLPE] (on)
[    0.141591]  (null): Device [PWM1] is in always present list
[    0.154810] ACPI: Power Resource [CLK0] (on)
[    0.154996] ACPI: Power Resource [CLK1] (on)
[    0.163531] ACPI: Power Resource [FN00] (off)
[    0.166219] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.166238] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.167165] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug SHPCHotplug PME]
[    0.168054] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[    0.168058] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[    0.170487] PCI host bridge to bus 0000:00
[    0.170496] pci_bus 0000:00: root bus resource [io  0x0070-0x0077]
[    0.170501] pci_bus 0000:00: root bus resource [io  0x0000-0x006f window]
[    0.170505] pci_bus 0000:00: root bus resource [io  0x0078-0x0cf7 window]
[    0.170510] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.170514] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.170518] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.170523] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[    0.170527] pci_bus 0000:00: root bus resource [mem 0x80000000-0x80436ffe window]
[    0.170532] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.170551] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[    0.171104] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[    0.171134] pci 0000:00:14.0: reg 0x10: [mem 0x80400000-0x8040ffff 64bit]
[    0.171220] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.171711] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[    0.171748] pci 0000:00:1a.0: reg 0x10: [mem 0x80100000-0x801fffff]
[    0.171765] pci 0000:00:1a.0: reg 0x14: [mem 0x80000000-0x800fffff]
[    0.171891] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    0.172497] pci 0000:00:1c.0: [8086:0f48] type 01 class 0x060400
[    0.172600] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.173099] pci 0000:00:1c.1: [8086:0f4a] type 01 class 0x060400
[    0.173197] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.173682] pci 0000:00:1c.2: [8086:0f4c] type 01 class 0x060400
[    0.173779] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.174257] pci 0000:00:1c.3: [8086:0f4e] type 01 class 0x060400
[    0.174354] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.174835] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[    0.175394] pci 0000:00:1f.3: [8086:0f12] type 00 class 0x0c0500
[    0.175445] pci 0000:00:1f.3: reg 0x10: [mem 0x80418000-0x8041801f]
[    0.175523] pci 0000:00:1f.3: reg 0x20: [io  0xe000-0xe01f]
[    0.176213] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.176400] pci 0000:02:00.0: [10ec:8136] type 00 class 0x020000
[    0.176455] pci 0000:02:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.176493] pci 0000:02:00.0: reg 0x18: [mem 0x80304000-0x80304fff 64bit]
[    0.176519] pci 0000:02:00.0: reg 0x20: [mem 0x80300000-0x80303fff 64bit pref]
[    0.176668] pci 0000:02:00.0: supports D1 D2
[    0.176672] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.188055] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.188063] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    0.188069] pci 0000:00:1c.1:   bridge window [mem 0x80300000-0x803fffff]
[    0.188217] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.188398] pci 0000:04:00.0: [10ec:8136] type 00 class 0x020000
[    0.188457] pci 0000:04:00.0: reg 0x10: [io  0xc000-0xc0ff]
[    0.188495] pci 0000:04:00.0: reg 0x18: [mem 0x80204000-0x80204fff 64bit]
[    0.188521] pci 0000:04:00.0: reg 0x20: [mem 0x80200000-0x80203fff 64bit pref]
[    0.188674] pci 0000:04:00.0: supports D1 D2
[    0.188679] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.200050] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.200057] pci 0000:00:1c.3:   bridge window [io  0xc000-0xcfff]
[    0.200063] pci 0000:00:1c.3:   bridge window [mem 0x80200000-0x802fffff]
[    0.202341] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.202724] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.203105] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.203496] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.203871] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.204263] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.204637] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.205011] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 12 14 15) *0, disabled.
[    0.224919] SCSI subsystem initialized
[    0.225042] libata version 3.00 loaded.
[    0.225042] vgaarb: loaded
[    0.225042] ACPI: bus type USB registered
[    0.225042] usbcore: registered new interface driver usbfs
[    0.225042] usbcore: registered new interface driver hub
[    0.225042] usbcore: registered new device driver usb
[    0.440871] EDAC MC: Ver: 3.0.0
[    0.440871] Registered efivars operations
[    0.444517] PCI: Using ACPI for IRQ routing
[    0.451990] PCI: pci_cache_line_size set to 64 bytes
[    0.452062] e820: reserve RAM buffer [mem 0x0003f000-0x0003ffff]
[    0.452066] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
[    0.452069] e820: reserve RAM buffer [mem 0x76be1000-0x77ffffff]
[    0.452073] e820: reserve RAM buffer [mem 0x7752a000-0x77ffffff]
[    0.452075] e820: reserve RAM buffer [mem 0x789e5000-0x7bffffff]
[    0.452078] e820: reserve RAM buffer [mem 0x79000000-0x7bffffff]
[    0.452379] NetLabel: Initializing
[    0.452382] NetLabel:  domain hash size = 128
[    0.452383] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.452432] NetLabel:  unlabeled traffic allowed by default
[    0.453121] clocksource: Switched to clocksource refined-jiffies
[    0.491247] VFS: Disk quotas dquot_6.6.0
[    0.491293] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.491594] AppArmor: AppArmor Filesystem Enabled
[    0.491700] pnp: PnP ACPI init
[    0.491883] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.492417] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.492424] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.492428] system 00:01: [io  0x0500-0x05fe] has been reserved
[    0.492433] system 00:01: [io  0x0600-0x061f] has been reserved
[    0.492450] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.493790] system 00:02: [mem 0xe0000000-0xefffffff] has been reserved
[    0.493797] system 00:02: [mem 0xfed01000-0xfed01fff] has been reserved
[    0.493802] system 00:02: [mem 0xfed03000-0xfed03fff] has been reserved
[    0.493807] system 00:02: [mem 0xfed04000-0xfed04fff] has been reserved
[    0.493813] system 00:02: [mem 0xfed0c000-0xfed0ffff] could not be reserved
[    0.493818] system 00:02: [mem 0xfed08000-0xfed08fff] has been reserved
[    0.493823] system 00:02: [mem 0xfed1c000-0xfed1cfff] has been reserved
[    0.493829] system 00:02: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.493834] system 00:02: [mem 0xfef00000-0xfeffffff] has been reserved
[    0.493850] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.499066] pnp: PnP ACPI: found 3 devices
[    0.509082] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.509113] clocksource: Switched to clocksource acpi_pm
[    0.509144] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[    0.509153] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[    0.509165] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000 add_align 100000
[    0.509179] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    0.509191] pci 0000:00:1c.2: bridge window [io  0x1000-0x0fff] to [bus 03] add_size 1000
[    0.509197] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[    0.509203] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000 add_align 100000
[    0.509216] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000
[    0.509242] pci 0000:00:1c.0: BAR 14: no space for [mem size 0x00200000]
[    0.509247] pci 0000:00:1c.0: BAR 14: failed to assign [mem size 0x00200000]
[    0.509261] pci 0000:00:1c.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509266] pci 0000:00:1c.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509278] pci 0000:00:1c.1: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509283] pci 0000:00:1c.1: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509291] pci 0000:00:1c.2: BAR 14: no space for [mem size 0x00200000]
[    0.509295] pci 0000:00:1c.2: BAR 14: failed to assign [mem size 0x00200000]
[    0.509307] pci 0000:00:1c.2: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509312] pci 0000:00:1c.2: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509324] pci 0000:00:1c.3: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509329] pci 0000:00:1c.3: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509337] pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.509344] pci 0000:00:1c.2: BAR 13: assigned [io  0x2000-0x2fff]
[    0.509361] pci 0000:00:1c.3: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509366] pci 0000:00:1c.3: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509374] pci 0000:00:1c.2: BAR 14: no space for [mem size 0x00200000]
[    0.509378] pci 0000:00:1c.2: BAR 14: failed to assign [mem size 0x00200000]
[    0.509390] pci 0000:00:1c.2: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509395] pci 0000:00:1c.2: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509407] pci 0000:00:1c.1: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509412] pci 0000:00:1c.1: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509419] pci 0000:00:1c.0: BAR 14: no space for [mem size 0x00200000]
[    0.509424] pci 0000:00:1c.0: BAR 14: failed to assign [mem size 0x00200000]
[    0.509436] pci 0000:00:1c.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.509440] pci 0000:00:1c.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.509447] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.509452] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    0.509467] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.509472] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    0.509479] pci 0000:00:1c.1:   bridge window [mem 0x80300000-0x803fffff]
[    0.509488] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.509493] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    0.509506] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.509511] pci 0000:00:1c.3:   bridge window [io  0xc000-0xcfff]
[    0.509518] pci 0000:00:1c.3:   bridge window [mem 0x80200000-0x802fffff]
[    0.509529] pci_bus 0000:00: resource 4 [io  0x0070-0x0077]
[    0.509533] pci_bus 0000:00: resource 5 [io  0x0000-0x006f window]
[    0.509537] pci_bus 0000:00: resource 6 [io  0x0078-0x0cf7 window]
[    0.509542] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.509546] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    0.509550] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    0.509554] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[    0.509559] pci_bus 0000:00: resource 11 [mem 0x80000000-0x80436ffe window]
[    0.509563] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    0.509568] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    0.509572] pci_bus 0000:02: resource 1 [mem 0x80300000-0x803fffff]
[    0.509577] pci_bus 0000:03: resource 0 [io  0x2000-0x2fff]
[    0.509581] pci_bus 0000:04: resource 0 [io  0xc000-0xcfff]
[    0.509585] pci_bus 0000:04: resource 1 [mem 0x80200000-0x802fffff]
[    0.509991] NET: Registered protocol family 2
[    0.510599] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.510705] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.510823] TCP: Hash tables configured (established 16384 bind 16384)
[    0.510953] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.510990] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.511146] NET: Registered protocol family 1
[    0.511840] PCI: CLS 64 bytes, default 64
[    0.511978] Unpacking initramfs...
[    2.573785] Freeing initrd memory: 54348K
[    2.574081] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1336e3dbd1a, max_idle_ns: 440795236868 ns
[    2.574114] clocksource: Switched to clocksource tsc
[    2.574215] Scanning for low memory corruption every 60 seconds
[    2.575902] Initialise system trusted keyrings
[    2.575941] Key type blacklist registered
[    2.576121] workingset: timestamp_bits=36 max_order=19 bucket_order=0
[    2.580120] zbud: loaded
[    2.581635] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.582135] fuse init (API version 7.26)
[    2.586298] Key type asymmetric registered
[    2.586302] Asymmetric key parser 'x509' registered
[    2.586431] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    2.586528] io scheduler noop registered
[    2.586531] io scheduler deadline registered
[    2.586625] io scheduler cfq registered (default)
[    2.588376] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    2.588587] intel_idle: MWAIT substates: 0x3000020
[    2.588591] intel_idle: v0.4.1 model 0x37
[    2.588799] intel_idle: lapic_timer_reliable_states 0xffffffff
[    2.589136] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    2.589162] ACPI: Power Button [PWRB]
[    2.589310] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    2.589361] ACPI: Power Button [PWRF]
[    2.597104] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    2.597655] thermal LNXTHERM:00: registered as thermal_zone0
[    2.597659] ACPI: Thermal Zone [TZ01] (42 C)
[    2.598157] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    2.618500] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    2.624719] hpet: number irqs doesn't agree with number of timers
[    2.624933] Linux agpgart interface v0.103
[    2.636413] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0xFE, rev-id 4)
[    2.706788] loop: module loaded
[    2.707797] libphy: Fixed MDIO Bus: probed
[    2.707801] tun: Universal TUN/TAP device driver, 1.6
[    2.707918] PPP generic driver version 2.4.2
[    2.708120] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.708130] ehci-pci: EHCI PCI platform driver
[    2.708169] ehci-platform: EHCI generic platform driver
[    2.708218] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.708225] ohci-pci: OHCI PCI platform driver
[    2.708249] ohci-platform: OHCI generic platform driver
[    2.708281] uhci_hcd: USB Universal Host Controller Interface driver
[    2.708744] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    2.708763] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    2.709885] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    2.709894] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    2.710278] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.710284] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.710288] usb usb1: Product: xHCI Host Controller
[    2.710292] usb usb1: Manufacturer: Linux 4.15.0-1031-oem xhci-hcd
[    2.710295] usb usb1: SerialNumber: 0000:00:14.0
[    2.710662] hub 1-0:1.0: USB hub found
[    2.710688] hub 1-0:1.0: 6 ports detected
[    2.712347] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    2.712360] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    2.712371] xhci_hcd 0000:00:14.0: Host supports USB 3.0  SuperSpeed
[    2.712511] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    2.712517] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.712521] usb usb2: Product: xHCI Host Controller
[    2.712524] usb usb2: Manufacturer: Linux 4.15.0-1031-oem xhci-hcd
[    2.712528] usb usb2: SerialNumber: 0000:00:14.0
[    2.712880] hub 2-0:1.0: USB hub found
[    2.712903] hub 2-0:1.0: 1 port detected
[    2.713464] i8042: PNP: No PS/2 controller found.
[    2.713654] mousedev: PS/2 mouse device common for all mice
[    2.714014] rtc_cmos 00:00: RTC can wake from S4
[    2.714207] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[    2.714252] rtc_cmos 00:00: alarms up to one month, y3k, 242 bytes nvram
[    2.714282] i2c /dev entries driver
[    2.714754] pcie_mp2_amd: AMD(R) PCI-E MP2 Communication Driver Version: 1.0
[    2.715016] device-mapper: uevent: version 1.0.3
[    2.715227] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    2.715240] intel_pstate: Intel P-state driver initializing
[    2.715540] ledtrig-cpu: registered to indicate activity on CPUs
[    2.715554] EFI Variables Facility v0.08 2004-May-17
[    2.722820] NET: Registered protocol family 10
[    2.740788] Segment Routing with IPv6
[    2.740849] NET: Registered protocol family 17
[    2.741117] Key type dns_resolver registered
[    2.742562] RAS: Correctable Errors collector initialized.
[    2.743022] microcode: sig=0x30679, pf=0x1, revision=0x90a
[    2.743153] microcode: Microcode Update Driver: v2.2.
[    2.743183] sched_clock: Marking stable (2742079115, 0)->(2724644374, 17434741)
[    2.743811] registered taskstats version 1
[    2.743837] Loading compiled-in X.509 certificates
[    2.753513] Loaded X.509 cert 'Build time autogenerated kernel key: 2285696422d14b0591cbf482b7d1f0729feb2d65'
[    2.753783] Loaded UEFI:db cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53' linked to secondary sys keyring
[    2.753873] Loaded UEFI:db cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4' linked to secondary sys keyring
[    2.753937] Couldn't get size: 0x800000000000000e
[    2.759210] MODSIGN: Couldn't get UEFI MokListRT
[    2.759529] zswap: loaded using pool lzo/zbud
[    2.775213] Key type big_key registered
[    2.775225] Key type trusted registered
[    2.783789] Key type encrypted registered
[    2.783800] AppArmor: AppArmor sha1 policy hashing enabled
[    2.795015] ima: Allocated hash algorithm: sha1
[    2.899127] evm: HMAC attrs: 0x1
[    2.899950]   Magic number: 12:458:286
[    2.899975] ppp ppp: hash matches
[    2.900595] rtc_cmos 00:00: setting system clock to 2012-01-01 16:15:17 UTC (1325434517)
[    2.901825] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.901827] EDD information not available.
[    2.931561] Freeing unused kernel memory: 2416K
[    2.940480] Write protecting the kernel read-only data: 20480k
[    2.943302] Freeing unused kernel memory: 2008K
[    2.959219] Freeing unused kernel memory: 1860K
[    2.988190] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.988193] x86/mm: Checking user space page tables
[    3.016619] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    3.048074] usb 1-4: new high-speed USB device number 2 using xhci_hcd
[    3.196554] usb 1-4: New USB device found, idVendor=03eb, idProduct=2404
[    3.196560] usb 1-4: New USB device strings: Mfr=0, Product=0, SerialNumber=3
[    3.196564] usb 1-4: SerialNumber: USB CAN FD Application v.B
[    3.502136] sdhci: unknown parameter 'debug_quiks2' ignored
[    3.502255] sdhci: Secure Digital Host Controller Interface driver
[    3.502257] sdhci: Copyright(c) Pierre Ossman
[    3.528805] mmc0: SDHCI controller on ACPI [80860F14:01] using ADMA
[    3.534342] mmc1: SDHCI controller on ACPI [INT33BB:00] using ADMA
[    3.540793] mmc2: SDHCI controller on ACPI [80860F16:00] using ADMA
[    3.541177] wmi_bus wmi_bus-PNP0C14:00: WQBC data block query control method not found
[    3.550887] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    3.566336] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.566359] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
[    3.576744] r8169 0000:02:00.0 eth0: RTL8106e at 0x        (ptrval), 00:4e:01:b9:aa:25, XID 04900000 IRQ 89
[    3.576843] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.576859] r8169 0000:04:00.0: can't disable ASPM; OS doesn't have ASPM control
[    3.599603] mmc1: new high speed SDIO card at address fffd
[    3.604380] r8169 0000:04:00.0 eth1: RTL8106e at 0x        (ptrval), 00:4e:01:b9:aa:26, XID 04900000 IRQ 90
[    3.632735] mmc0: new HS200 MMC card at address 0001
[    3.647839] SSE version of gcm_enc/dec engaged.
[    3.782627] mmcblk0: mmc0:0001 W32508 7.13 GiB
[    3.782941] mmcblk0boot0: mmc0:0001 W32508 partition 1 4.00 MiB
[    3.783199] mmcblk0boot1: mmc0:0001 W32508 partition 2 4.00 MiB
[    3.783351] mmcblk0rpmb: mmc0:0001 W32508 partition 3 4.00 MiB, chardev (243:0)
[    3.809408]  mmcblk0: p1 p2 p3 p4
[    3.816946] random: fast init done
[    3.817048] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    3.817083] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    3.817130] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    5.552364] raid6: sse2x1   gen()   796 MB/s
[    5.600368] raid6: sse2x1   xor()  1308 MB/s
[    5.648400] raid6: sse2x2   gen()  1180 MB/s
[    5.696361] raid6: sse2x2   xor()  1552 MB/s
[    5.744359] raid6: sse2x4   gen()  1783 MB/s
[    5.792352] raid6: sse2x4   xor()  1667 MB/s
[    5.792356] raid6: using algorithm sse2x4 gen() 1783 MB/s
[    5.792357] raid6: .... xor() 1667 MB/s, rmw enabled
[    5.792360] raid6: using ssse3x2 recovery algorithm
[    5.797553] xor: measuring software checksum speed
[    5.836013]    prefetch64-sse:  4036.000 MB/sec
[    5.876010]    generic_sse:  3671.000 MB/sec
[    5.876013] xor: using function: prefetch64-sse (4036.000 MB/sec)
[    5.881814] async_tx: api initialized (async)
[    6.119771] Btrfs loaded, crc32c=crc32c-intel
[    6.445707] EXT4-fs (mmcblk0p4): INFO: recovery required on readonly filesystem
[    6.445711] EXT4-fs (mmcblk0p4): write access will be enabled during recovery
[    6.519174] EXT4-fs (mmcblk0p4): recovery complete
[    6.523141] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[    7.077930] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.108618] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    7.129487] systemd[1]: Detected architecture x86-64.
[    7.135999] systemd[1]: Set hostname to <4F4HP42>.
[    7.294584] systemd-gpt-auto-generator[401]: Failed to dissect: Input/output error
[    7.531840] systemd[391]: /lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1.
[    7.778692] systemd[1]: Created slice System Slice.
[    7.779537] systemd[1]: Listening on Syslog Socket.
[    7.779848] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    7.780624] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.781021] systemd[1]: Listening on udev Control Socket.
[    7.781431] systemd[1]: Listening on Journal Socket.
[    7.876799] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    8.005116] Loading iSCSI transport class v2.0-870.
[    8.071735] iscsi: registered transport (tcp)
[    8.223796] EXT4-fs (mmcblk0p4): re-mounted. Opts: (null)
[    8.303479] iscsi: registered transport (iser)
[    8.420713] systemd-journald[429]: Received request to flush runtime journal from PID 1
[    8.556993] systemd-journald[429]: File /var/log/journal/c1fde2292bcc4562bd9a270701a11b94/system.journal corrupted or uncleanly shut down, renaming and replacing.
[   10.568599] 80860F0A:00: ttyS4 at MMIO 0x8047f000 (irq = 39, base_baud = 2764800) is a 16550A
[   10.568952] serial serial0: tty port ttyS4 registered
[   10.569329] ttyS4 - failed to request DMA
[   10.588365] 80860F0A:01: ttyS5 at MMIO 0x80485000 (irq = 40, base_baud = 2764800) is a 16550A
[   10.588649] serial serial1: tty port ttyS5 registered
[   10.608512] ttyS5 - failed to request DMA
[   10.808104] st-accel-i2c i2c-SMO8A90:00: i2c-SMO8A90:00 supply vdd not found, using dummy regulator
[   10.808164] st-accel-i2c i2c-SMO8A90:00: i2c-SMO8A90:00 supply vddio not found, using dummy regulator
[   10.840644] dw_dmac INTL9C60:00: DesignWare DMA Controller, 8 channels
[   10.851833] iio iio:device1: registered accelerometer lng2dm
[   10.852544] st-press-i2c i2c-SMO9210:00: i2c-SMO9210:00 supply vdd not found, using dummy regulator
[   10.852603] st-press-i2c i2c-SMO9210:00: i2c-SMO9210:00 supply vddio not found, using dummy regulator
[   10.856335] iio iio:device2: registered pressure sensor lps22hb
[   10.880612] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[   11.378970] cdc_acm 1-4:1.0: ttyACM0: USB ACM device
[   11.388664] usbcore: registered new interface driver cdc_acm
[   11.388668] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   11.998468] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   12.038887] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   12.131277] input: Dell WMI hotkeys as /devices/platform/PNP0C14:00/wmi_bus/wmi_bus-PNP0C14:00/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input2
[   12.766494] Bluetooth: Core ver 2.22
[   12.766562] NET: Registered protocol family 31
[   12.766565] Bluetooth: HCI device and connection manager initialized
[   12.766574] Bluetooth: HCI socket layer initialized
[   12.766580] Bluetooth: L2CAP socket layer initialized
[   12.766596] Bluetooth: SCO socket layer initialized
[   12.910148] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   12.910296] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   12.910406] intel_soc_dts_thermal: request_threaded_irq ret -22
[   13.114335] rsi_91x: ================================================
[   13.114340] rsi_91x: ================ RSI Version Info ==============
[   13.114342] rsi_91x: ================================================
[   13.114346] rsi_91x: FW Version	: 1.6.1
[   13.114350] rsi_91x: Operating mode	: 13 [Wi-Fi STA + BT DUAL]
[   13.114353] rsi_91x: Firmware file	: rsi/rs9113_wlan_bt_dual_mode.rps
[   13.114355] rsi_91x: ================================================
[   13.338341] rsi_91x: ***** Firmware Loading successful *****
[   13.368991] rsi_91x: Max Stations Allowed = 1
[   16.568587] Adding 1048572k swap on /dev/mmcblk0p3.  Priority:-2 extents:1 across:1048572k SSFS
[   16.572044] FAT-fs (mmcblk0p2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   17.182201] audit: type=1400 audit(1677236524.447:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=731 comm="apparmor_parser"
[   17.182215] audit: type=1400 audit(1677236524.447:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=731 comm="apparmor_parser"
[   17.182225] audit: type=1400 audit(1677236524.447:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=731 comm="apparmor_parser"
[   17.182233] audit: type=1400 audit(1677236524.447:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=731 comm="apparmor_parser"
[   17.189753] audit: type=1400 audit(1677236524.455:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/lxc-start" pid=732 comm="apparmor_parser"
[   17.201154] audit: type=1400 audit(1677236524.467:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=733 comm="apparmor_parser"
[   17.201170] audit: type=1400 audit(1677236524.467:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=733 comm="apparmor_parser"
[   17.201181] audit: type=1400 audit(1677236524.467:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=733 comm="apparmor_parser"
[   17.216324] audit: type=1400 audit(1677236524.483:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lxc-container-default" pid=730 comm="apparmor_parser"
[   17.216339] audit: type=1400 audit(1677236524.483:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lxc-container-default-cgns" pid=730 comm="apparmor_parser"
[   17.496290] new mount options do not match the existing superblock, will be ignored
[   17.928689] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.928694] Bluetooth: BNEP filters: protocol multicast
[   17.928704] Bluetooth: BNEP socket layer initialized
[   19.084719] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.312148] r8169 0000:02:00.0 eth0: link down
[   19.312178] r8169 0000:02:00.0 eth0: link down
[   19.312339] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.340549] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   19.564111] r8169 0000:04:00.0 eth1: link down
[   19.564270] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   19.591041] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.591277] rsi_91x: ===> Interface UP <===
[   19.594567] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.594592] rsi_91x: rsi_disable_ps: Cannot accept disable PS in PS_NONE state
[   19.877645] rsi_91x: rsi_mac80211_add_interface: Interface type 10 not supported
[   19.933907] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.937678] rsi_91x: rsi_disable_ps: Cannot accept disable PS in PS_NONE state
[   20.898850] r8169 0000:02:00.0 eth0: link up
[   20.898869] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   26.838936] iTCO_vendor_support: vendor-support=0
[   26.851926] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   26.853099] iTCO_wdt: Found a Bay Trail SoC TCO device (Version=3, TCOBASE=0x0460)
[   26.854365] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[  195.855746] random: crng init done
[  195.855758] random: 7 urandom warning(s) missed due to ratelimiting
edgegateway3002.txt · Last modified: 2023/02/24 18:45 by millerjs
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0