edgegateway3002
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| edgegateway3002 [2023/02/24 18:04] – [Local Access] millerjs | edgegateway3002 [2024/11/14 02:30] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 9: | Line 9: | ||
| ===== General Notes ===== | ===== General Notes ===== | ||
| + | ==== Specs ==== | ||
| + | * Intel Atom E3805 2x 1.33GHz | ||
| + | * 2GB RAM (DDR3L @ 1600MHz) | ||
| + | * 8GB eMMC (Kingston W32508) | ||
| + | * 2x Realtek RTL8101 at 10/100. Port 1 (eth0) supports PoE power input! | ||
| + | * [[https:// | ||
| + | * [[https:// | ||
| + | * ZigBee 2.4GHz - Attached at /dev/ttyHS0 ([[https:// | ||
| + | * CAN bus on / | ||
| + | * Environmental Sensors | ||
| + | * ST Micro HTS221 - Temperature | ||
| + | * ST Micro LNG2DMTR - Accelerometer | ||
| + | * ST Micro LPS22HB - Barometric Pressure | ||
| - | ==== Local Access ==== | + | ==== Available External Interfaces ==== |
| - | The 3002 was designed to be accessed entirely over a network, and has no end user ways to accessing a local console. Under the lid there is a four pin JST micro connector that can be used to access ttyS0, which has console output on boot. This is a 1v8 UART running at 115200,8n1. | + | * 2x RJ-45 Ethernet |
| + | * 1x USB 3.0 (600mA) | ||
| + | * 1x USB 2.0 (400mA) | ||
| + | * SMA-F for GNSS/ | ||
| + | * SMA-F for Zigbee | ||
| + | * (2x additional openings for SMA available) | ||
| + | * 3 pin phoenix connector for CAN bus | ||
| + | * 3 pin phoenix connector for power 12-57v DC (plus ignition detection) | ||
| + | * 3.5mm jack for external intrusion detection | ||
| + | * uSD slot behind screwed down door | ||
| + | * 3x LEDs | ||
| + | * Power LED (orange/ | ||
| + | * " | ||
| + | * " | ||
| + | |||
| + | ==== Available Internal Interfaces ==== | ||
| + | * 4 pin JST micro connector for ttyS0 (115200,8n1 for boot console) | ||
| + | * MiniPCIe connector (not soldered, likely needs additional hardware) | ||
| + | * Four switches exist inside the device (two 2 switch modules) but it is not yet clear exactly what they do. | ||
| + | |||
| + | No user upgradable RAM/ | ||
| + | ==== Local Console | ||
| + | The 3002 was designed to be accessed entirely over a network, and has no end user ways to accessing a local console. Under the lid there is a four pin JST micro connector | ||
| {{:: | {{:: | ||
| ==== UEFI Access ==== | ==== UEFI Access ==== | ||
| - | The 3002 has no video output, and was designed to have the BIOS be accessed via a tool called Dell Command Configure Version. This can be installed via debs available here: {{ :: | + | The 3002 has no video output, and was designed to have the BIOS be accessed via a tool called Dell Command Configure Version. This can be installed via debs available here: |
| + | |||
| + | {{ :: | ||
| + | |||
| + | <note important> | ||
| ==== Environmental Sensors ==== | ==== Environmental Sensors ==== | ||
| === GNSS === | === GNSS === | ||
| The UBX-M8030 can be accessed via /dev/ttyHS1 running at 9600,8n1 by default. It supports three concurrent SVs (GPS, GLONASS, and BeiDou) and is very sensitive. The GNSS module and WiFi+BT module share an RF connection for some reason, and as such the GNSS does not provide any power for an active antenna. | The UBX-M8030 can be accessed via /dev/ttyHS1 running at 9600,8n1 by default. It supports three concurrent SVs (GPS, GLONASS, and BeiDou) and is very sensitive. The GNSS module and WiFi+BT module share an RF connection for some reason, and as such the GNSS does not provide any power for an active antenna. | ||
| - | We are currently researching how to add power to this connection to support an active antenna, which greatly improves the performance of most GNSS antennas which have built in low noise amplifiers (LNAs). | + | <note important> |
| === Temp/ | === Temp/ | ||
| Line 50: | Line 89: | ||
| ==== Flash Recovery Image ==== | ==== Flash Recovery Image ==== | ||
| - | More testing needed. Watch this space! | + | <note tip>More testing needed. Watch this space!</ |
| - | ===== Specs & Hardware ===== | + | ===== Hardware |
| - | * Intel Atom E3805 2x 1.33GHz | + | |
| - | * 2GB RAM (DDR3L) | + | |
| - | * 8GB eMMC (Kingston | + | |
| - | * 2x Realtek RTL8101 at 10/100. Port 1 (eth0) supports PoE power input! | + | |
| - | * [[https:// | + | |
| - | * [[https:// | + | |
| - | * ZigBee 2.4GHz - Attached at /dev/ttyHS0 ([[https:// | + | |
| - | * CAN bus on / | + | |
| - | * Environmental Sensors | + | |
| - | * ST Micro HTS221 - Temperature | + | |
| - | * ST Micro LNG2DMTR - Accelerometer | + | |
| - | * ST Micro LPS22HB - Barometric Pressure | + | |
| ==== lshw ==== | ==== lshw ==== | ||
edgegateway3002.1677261895.txt.gz · Last modified: 2024/11/14 02:30 (external edit)