User Tools

Site Tools


edgegateway3002


Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
edgegateway3002 [2023/02/24 18:10] – [Specs & Hardware] millerjsedgegateway3002 [2024/11/14 02:30] (current) – external edit 127.0.0.1
Line 9: Line 9:
  
 ===== General Notes ===== ===== General Notes =====
 +==== Specs ====
 +  * Intel Atom E3805 2x 1.33GHz
 +  * 2GB RAM (DDR3L @ 1600MHz)
 +  * 8GB eMMC (Kingston W32508)
 +  * 2x Realtek RTL8101 at 10/100. Port 1 (eth0) supports PoE power input!
 +  * [[https://www.silabs.com/documents/login/data-sheets/RS9113_Module_Family_Datasheet.pdf|SiLabs RS9113]] WiFi+Bluetooth over SDIO
 +  * [[https://www.u-blox.com/en/product/ubx-m8030-series?legacy=Current#Document-&-resources|Ublox UBX-M8030]] GNSS - connected at /dev/ttyHS1
 +  * ZigBee 2.4GHz - Attached at /dev/ttyHS0 ([[https://www.silabs.com/documents/public/data-sheets/TG-PM-0509-ETRX358x.pdf|SiLabs ETRX3587HR]])
 +  * CAN bus on /dev/ttyACM0 - Atmel ATSAME70N19A-CNT. Exposed on 3pin Phoenix header on the side. 
 +  * Environmental Sensors
 +    * ST Micro HTS221 - Temperature
 +    * ST Micro LNG2DMTR - Accelerometer
 +    * ST Micro LPS22HB - Barometric Pressure 
  
-==== Local Access ====+==== Available External Interfaces ==== 
 +  * 2x RJ-45 Ethernet 
 +  * 1x USB 3.0 (600mA) 
 +  * 1x USB 2.0 (400mA) 
 +  * SMA-F for GNSS/WiFi+BT 
 +  * SMA-F for Zigbee 
 +  * (2x additional openings for SMA available) 
 +  * 3 pin phoenix connector for CAN bus 
 +  * 3 pin phoenix connector for power 12-57v DC (plus ignition detection) 
 +  * 3.5mm jack for external intrusion detection 
 +  * uSD slot behind screwed down door 
 +  * 3x LEDs 
 +      * Power LED (orange/green, shows generic status info) 
 +      * "Antenna" LED (green, not sure how it's controlled) 
 +      * "Cloud" LED (green, controlled by end user though GPIO sysfs) 
 + 
 +==== Available Internal Interfaces ==== 
 +  * 4 pin JST micro connector for ttyS0 (115200,8n1 for boot console) 
 +  * MiniPCIe connector (not soldered, likely needs additional hardware) 
 +  * Four switches exist inside the device (two 2 switch modules) but it is not yet clear exactly what they do.  
 + 
 +No user upgradable RAM/storage. 
 +==== Local Console Access ====
 The 3002 was designed to be accessed entirely over a network, and has no end user ways to accessing a local console. Under the lid there is a four pin JST micro connector (same //physical// connector as Qwiic) that can be used to access ttyS0, which has console output on boot. This is a 1v8 UART running at 115200,8n1. The 3002 was designed to be accessed entirely over a network, and has no end user ways to accessing a local console. Under the lid there is a four pin JST micro connector (same //physical// connector as Qwiic) that can be used to access ttyS0, which has console output on boot. This is a 1v8 UART running at 115200,8n1.
  
edgegateway3002.1677262226.txt.gz · Last modified: 2024/11/14 02:30 (external edit)

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki